ORing Industrial 1-port Gigabit High Power PoE++ Injector (INJ-101GT++-60W-24)


Product Tags:
ORing Industrial 1-port Gigabit High Power PoE++ Injector (INJ-101GT++-60W-24)

The INJ-101GT++ PoE Injector series is not only an IEEE802.3at compliant device but also an advanced high power PoE injector. It is intelligent detection that provided 1-ports 10/100/1000Base-T (X) PoE outputs.

The device does not turn on power until it detects a valid PoE signature from the PoE devices attached downstream on the Ethernet cable.

This protection against damage to non-PoE compliant equipment which may be connected to the Ethernet cable. Therefore, only an IEEE 802.3at/802.3af compliant device can be powered with the INJ-101GT++ PoE Injector.

Typically in Gigabit networks the maximum allowable CAT5 cable length is about 100 meters, due to the limitation of the Ethernet standards. The INJ-101GT++ PoE Injector can function with any PoE P.D. equipment which is fully compliant with the IEEE 802.3af/at PoE standards, and provide the DIP switch configurator for High power PoE management.



  • PoE++ Injector for 1x10/100/1000Base-T(X)
  • Fully compliant with IEEE802.3at/802.3af standard
  • Auto protection for Over Voltage Power Input and over current output
  • Supports totallyPower Output up to 60Watts for all ports usage.
  • Support wide range power input, 9 to 57VDC
  • Provided DIP switch configurator for PoE mode management
  • High reliability and rigid IP-30 housing
  • DIN-Rail and Wall Mount Design



ORing Injector Model INJ-101GT++-60W-24V
Physical Ports  
RJ-45 Ethernet Port Input 1
RJ-45 Ethernet Port with P.S.E. Output 1
Operating Voltage  
Input Voltage 9 ~ 57 VDC on 4-pin terminal block
LED Indicators  
Power Indicator PWR / Ready: 1 x LED 
Green On: Power is on and functioning Normally.
PoE Indicators 1 x LED 
Blue On: PoE Device Link
Off : None PoE Device Detected
Blink (Blue) : Overload present
DIP Switch  
DIP Switch 1/2

DIP Switch 1/2 (OFF): PoE P.S.E set to master and Asyncronize mode

DIP Switch 1/2 (ON) : PoE P.S.E set to syncronize mode(default)
Input Power 9 ~ 57 VDC on 4-pin terminal block
Power Consumption 1 Watts (Not include PD's device)
PoE Power Budget 30Watt at 9~24VDC, 60Watt at 24~57VDC
Short Circuit Protection Present
Over Load Protection Present
Physical Characteristics  
Enclosure IP-30
Dimensions (W x D x H) 41(W)x70(D)x95(H)mm (1.03 x 2.76 x 3.74 inch)
Weight (g) 318 g
Storage Temperature -40 to 85°C (-40 to 185°F)
Operating Temperature -40 to 75°C (-40 to 167°F)
Operating Humidity 5% to 95% Non-condensing
Regulatory Approvals  
EMC CE EMC (EN55024,EN 55032), FCC Part 15 B
EMI EN55032, CISPR 32, EN61000-3-2, EN61000-3-3, FCC Part 15 B class A
EMS EN55024 (IEC/EN 61000-4-2 (ESD), IEC/EN 61000-4-3 (RS), IEC/EN 61000-4-4 (EFT), IEC/EN61000-4-5 (Surge), IEC/EN 61000-4-6 (CS), IEC/EN 61000-4-8 (PFMF), IEC/EN 61000-4-11 (DIP)
Shock IEC60068-2-27
Free Fall IEC60068-2-32
Vibration IEC60068-2-6
Safety EN60950-1
MTBF 2067004hrs
Warranty 5 years

*Note1: (1) By default, the output value of the high power PoE++ is in Sync mode which supports PoE af/at-compliant P.D. devices.

(2) If you cannot enable the 60W PTZ camera, please set the DIP switch to Async mode and reconnect power. This mode only supports Dual P.D mode. You may not connect to an af/at-compliant P.D. device with this mode.

Sold Out
Product Images (click to enlarge)
  • ORing Industrial 1-port Gigabit High Power PoE++ Injector (INJ-101GT++-60W-24)